Articles

Thermostat Removal

The stock GM thermostat is set to be fully open at around 195 - 203 deg F.

If you plan to take it out and test it, then keep in mind that the rubber seal (GM #10226107) is a 'one use' part and attempts to reuse it may be a waste of time and coolant, so have a new one on hand from your local GM dealer.

The only acceptable alternative Thermostat is the Stant (part #14068) which is fully open around 180 - 185 deg F. The seal that comes with it is not as good as the GM seal which is tapered on one side. You may also wish to drill a bleed hole in it, between 1/16 or 3/32" should be sufficient, and when you install it, remember that the bleed hole should be in the 12 o'clock position.

In general, lower temperature thermostats on electronically controlled engines will keep keep temperatures lower resulting in richer mixtures, more advanced spark, and some increase in power at the expense of fuel economy. A small but usually negligible impact on emissions will also occur. This assumes the engine temperature regulates around the thermostat opening point.

Removal of the Thermostat:

  1. Raise the car on the passenger side.
  2. Loosen the 2 bolts (13mm) clamping the thermostat seal, and the other 13 bolt on the bracket next to the thermostat bolt.
  3. Then remove the 2 bolts holding the thermostat to the front frame rail.
  4. Move the spring clamp holding the thermostat exit hose at the radiator.
  5. Remove the thermostat bolts.
  6. Wrestle the thermostat housing free and then you can remove the thermostat.
  7. Install a new seal and clean the two mounting surfaces of the thermostat housing.

Install the thermostat housing and hose back onto the radiator. Pry the housing back and install the thermostat (and seal), being careful to position the seal properly (taper side of seal facing out). You can try using a thin bladed screw driver to hold it in place. Then gently position the housing in place, install the 2 screws, lower screw first, then the upper screw and the bracket, etc.

I considered trying to use crazy glue to hold the seal in place, but didn't. The alternative, is the procedure in the GM service manual which entails removing BOTH haves of the thermostat housing and 5 hoses. It appears to me that this is extremely difficult to do without the radiator removed.

Radiator removal

If you desire an all Aluminum radiator, Fluidyne (www.fluidyne.com) makes a drop in replacement for the ZR-1, list price $620, and a dealer offered it to me for $520. I got a new GM radiator for my 93 for $300, hopefully it will last. Other radiators, such as the Lingenfelter are NOT drop in replacements.

Another fun task thanks to the good job the GM engineers did of DFM (Design for Maintenance). There are two problems that one will face when removing the upper radiator shroud for the first time. One is that the 7mm sheet metal screws on the lower sides of the shroud are difficult to reach and require a 7mm U-joint socket to get to them.

The Sears part # is 43193 (7mm flex socket).

The other problem is that parts of the flat part of the shroud on the passenger side should be cut away with a hack saw blade and holder to make removal easier. The problem is that one doesn't want to disconnect the oil cooler or AC lines. Lifting the shroud as delivered from the factory is ugly without cutting away part of the shroud. In my case I cut away a triangle area in the back that is about 2" x 3.2" including a slot for an 8mm bolt and trimmed some material around the 6mm hole in the middle (see picture). In either case, after removing all the bolts (including the 5 holding the fans to the shroud), you lift the shroud up and back on the drivers side, and then on the passenger side, clearing the oil cooler and AC lines. The rest of the procedure is straight forward and doesn't need any explanation.

Another trick suggested by Jim Milstead is to reverse the direction of the 7mm sheet metal screws (held in place by Tinnerman nuts) by filing some material from the lower shroud and moving the nuts to the upper shroud. The distance of the hole from the edge of the shroud is 3/8". You will have to file 1/8" from the lower hole and 1/16" from the middle hole. Use a coarse file or a hacksaw blade (and holder) to do it.

If you wish to remove the thermostat, do it with the radiator removed, in the case that you have to remove both halves of the thermostat housing to get the seal to seat.

 

Author: Steve Jasik

Actions: E-mail | Permalink |
  Disclaimer

The information contained in this website is for general information purposes only. Whilst we endeavor to keep the information up-to-date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk.

In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of or in connection with the use of this website.

Through this website there are links to other websites which are not under the control of the ZR-1 Net Registry. We have no control over the nature, content and availability of those sites. The inclusion of any links does not necessarily imply a recommendation or endorse the views expressed within them.

Read the full Disclaimer...

©2017 ZR-1 NET Registry   |  Privacy Statement